Call Today

 

Everyone maintains their own unique thinking with regards to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.

Setting up a tub isn't exactly rocket science, yet it does need solid plumbing, woodworking, as well as often, tiling skills. Replacing an old bath tub with a new one is also a reasonably challenging task. If the old tub is conveniently easily accessible, the project can relocate immediately; if you have to open a wall surface to eliminate the old bathtub as well as place the new bathtub, the job is much harder. In either case, the task is within a house handyman's skills, although you will certainly need an assistant to move out the old bathtub and also embeded in the brand-new one. See to it you have actually qualified on your own for the work as well as fit attempting it. Rather than hiring a service provider to take control of a halfway-completed project, it is much better to take into consideration using one prior to you start. Opportunities are you might need an expert plumber to make tube connections.
This article will assist you mount a brand-new bath tub in your bathroom if you have already purchased a new bathtub as well as don't require to alter the arrangement of your previous water supply pipelines.
Your tools and also material list must comprise the following:

 

• New Bath tub


• Hammer


• Pipe Wrenches


• Prybar


• Shatterproof glass


• Level


• Pliers


• Flexible Wrench


• Putty Blade


• Screwdriver


• Cold Chisel


• Measuring tape


• Pipeline Caps


 

Removing Old Touches

If you require to change old taps with brand-new ones as a part of your installation, after that the first thing you should do is detach the water. After doing so, activate the faucets to drain pipes any type of water staying in the system. The procedure of eliminating the existing taps can be fairly problematic due to the restricted access that is frequently the instance.
Use a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that attaches the supply pipelines to the taps. Have a cloth ready for the staying water that will certainly originate from the pipelines. Once the supply pipes have been gotten rid of, use the exact same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly need to stop the single taps from transforming during this procedure. When the faucets have been removed, the holes in the bath/basin will certainly need to be cleaned up of any kind of old sealing substance.
Prior to moving on to fit the new taps, contrast the pipeline links on the old taps to the new faucets. If the old faucets are longer than the brand-new taps, after that a shank adapter is needed for the new taps to fit.

 

 

Suitable New Taps

If the tails of the brand-new faucets are plastic, after that you will require a plastic connector to stop damage to the string. One end of the connector fits on the plastic tail of the tap as well as the various other end offers a link to the existing supply pipelines.
If you require to fit a monobloc, then you will need decreasing couplers, which links the 10mm pipeline of the monobloc to the basic 15mm supply pipe.
Next, position the tap in the mounting opening in the bath/basin guaranteeing that the washers are in location in between the tap as well as the sink. Secure the faucet in place with the maker offered backnut. Once the tap is firmly in place, the supply pipes can be linked to the tails of the taps. The faucets can either be connected by using corrugated copper piping or with typical faucet connectors. The previous kind ought to be linked to the tap finishes first, tightening just by hand. The supply pipes can later be connected to the various other end. Tighten both ends with a spanner after both ends have been attached.

 

 

Setting up the Bathtub

Utilizing the two wood boards under its feet, put the bathtub in the required placement. The wood boards are useful in uniformly spreading out the weight of the bath tub over the location of the boards instead of concentrating all the weight onto four tiny points.
The following goal is to ensure that the bath tub is leveled all round. This can be attained by examining the level and adjusting the feet on the bath tub up until the spirit level reviews level.
To mount faucets, fit the bottom of the outermost flexible faucet connector to the suitable supply pipeline by making a compression join; then do the very same for the various other faucet.
Turn on the water supply and inspect all joints and new pipework for leaks and also tighten them if necessary. Fill the bathtub as well as additionally inspect the overflow outlet and the normal outlet for leaks.
Lastly, deal with the bathroom paneling as described in the maker's instruction manual. Tiling as well as sealing around the tub should wait up until the bath tub has actually been made use of at the very least once as this will certainly resolve it right into its last setting.

 

 

Preparing for the Installment

First of all, the sustaining structure supplied with the bath must be fitted (if called for) according to the manufacturer's instructions. Next off, fit the taps or mixer to the bath tub. When suitable the faucet block, it is necessary to ensure that if the tap comes with a plastic washer, it is fitted in between the bathroom as well as the taps. On a plastic bath, it is likewise sensible to fit a sustaining plate under the faucets device to stop strain on the tub.
Fit the versatile tap connectors to the bottom of both taps making use of 2 nuts as well as olives (in some cases supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet via the hole in the bath. Make use of the nut provided by the manufacturer to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the versatile overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bath. Make sure you use every one of the provided washers.
Link the catch to the bottom of the waste outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Connect the bottom of the overflow tube in a similar manner.The bath must currently prepare to be suited its last setting.

 

 

Tiling Around the Bath tub

In the location where the bathroom meets the tile, it is required to secure the accompanies a silicone rubber caulking. This is necessary as the fitting can move sufficient to split a rigid seal, creating the water to pass through the wall in between the bath and also the tiling, causing complications with dampness as well as feasible leaks to the ceiling below.
You can pick from a selection of coloured sealants to blend in your components and also installations. They are sold in tubes and cartridges, as well as can securing voids approximately a size of 3mm (1/8 inch). If you have a bigger void to fill, you can load it with spins of soaked newspaper or soft rope. Remember to always fill up the tub with water before sealing, to enable the movement experienced when the tub remains in use. The sealer can split rather early if you do not take into account this movement prior to securing.
Additionally, ceramic coving or quadrant floor tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are likewise easily readily available on the marketplace. It is recommended to fit the ceramic tiles using waterproof or water-proof sticky and also grout.

 

How to Install a Freestanding Bathtub?

 

Installing a freestanding bathtub or any kind of bathtub is not a difficult task if you have a sophisticated guide on installing a freestanding bathtub in your bathroom. Aside from getting the freestanding bathtub to your bathroom, you can do all the work without paying a plumber. A bathroom with a bathtub is a retreat where you can feel the sensation of coming home and soaking in that hot water. It is a great way to remove all the stress from your day.

This guide will walk you through installing a freestanding bathtub in simple steps and help you find relief.

 

Slope

 

Make sure your bathroom has a proper slope. If your floor lacks a slope, the water flow to the drain will not function, which leads to a blocked drain which can cost you money. You can use the level device to see your bathroom's vertical and horizontal aspects. Once you have that information, you must carry out the next step.

 

Placement

 

A freestanding bathtub has a unique characteristic that helps you bring elegance to your bathroom. A freestanding bathtub comes in various sizes and shapes suitable for different types of bathrooms.

According to the information you gathered from the level device, you must pick a bathtub that suits your style and fits your bathroom aesthetically. You can place a freestanding bathtub virtually anywhere, such as in the corner, near the wall, or even at the center of your bathroom. However, you must ensure proper plumbing where you want to install the tub. If not, then you must call a plumber.

 

Clean the bathroom floor

 

After deciding where to place the bathtub, you must clean the entire bathroom floor so that the dust and debris do not accumulate underneath the tub. Simple cleaning is enough, and you will clean it again after the installation.

 

Steps to Install a Freestanding Bathtub:

 

STEP 1: Place the protective blanket in the adjacent area where you want to install the bathtub. It will help you protect the bathtub's sides when you do the installation.

STEP 2: Now, place the 4x4 lumber in the area where you want to install the bathtub. Place the bathtub on top of the lumber, and align the drain line with the bathtub drain.

STEP 3: A freestanding bathtub comes with a drain kit. If not, make sure you purchase one with your bathtub. You can pop that drain kit and align it with your bathroom drain line. Ensure that you tighten the drain nut enough so there is no water leakage. You must also clean the bathtub’s drain to remove the factory dirt and debris.

STEP 4: Clean the drain hole in your bathroom. It helps to do the installation without any water blockage. A drain cleaner or bleach will suffice. Once the drain dries entirely, take a small amount of clear silicon and place it around the underside of the pipe flange.

STEP 5: Attach the drain tailpiece to the bottom of the bathtub. Place the rubber or plastic bushing with the plumbing material at the top of the tailpiece and screw the drain nut up the tube until it tightens both the bathtub’s drain and the drain tailpiece. Now you must add the lubricant to the seal to ensure there is no water leakage in the pipe connection.

STEP 6: Place caulk around the bottom edge of the bathtub. Take out the lumbar support and carefully bring the bathtub to the floor. Use a damp cloth to clean the excess caulk and debris and plumber putty to cover the tub drains and the floor.

 

Tips to Maintain a Freestanding Bathtub:

 

• Always look for the clog in the drain. You can pull it out with a small stick if hair or debris is in the gutter.


 
• Use mild cleaning components, which will help you preserve the bathtub for a long time and will also help you remove surface-level scratches.


 
• Do not use strong solutions such as concentrated bleach to remove stains. Instead, mix water and diluted bleach with a ratio of 10:2, respectively. Apply it to the tub's surface and leave it for 15-20 minutes to remove any surface-level stains.


 
• Always check the floor drain. You may unclog it using any small sticks or a small vacuum to suck out all the debris.


 
• Check the heater or faucet immediately if you smell rust or grease in the water. Rust in the water may stain or damage the bathtub in the long run.


 
• If you want to sand the bathtub, try using 400 grit sandpaper or 600 grit sandpaper for a more refined finish.

 

https://www.magnushomeproducts.com/blogs/inspired-living/how-to-install-a-freestanding-bathtub-a-diy-method-with-6-steps

 

I recently found that blog posting about How to Install a Bathtub when doing a search on the search engines. Remember to take a moment to promote this entry if you enjoyed it. I thank you for reading our article about How to Install a Bathtub Yourself.

Schedule Free Estimate